Pricing and fees
Setting Your Firm’s Hourly Rates from Your Costs
An engineering firm’s hourly rate is a person’s salary cost per hour multiplied up to cover the firm’s overhead and a profit. Set from your own costs, it covers them and the profit the firm plans; the market shows how much room there is above it.
On this page
Terms Used
- Salary cost per hour: a person’s annual salary divided by the hours they are paid for in a year.
- Overhead rate: the firm’s indirect costs divided by direct labour, the salary cost of hours charged to projects.
- Break-even multiplier: one plus the overhead rate; the factor at which a billed hour covers its share of every cost.
- Billing multiplier: the factor that turns salary cost per hour into the hourly rate, profit included.
- Realization: the share of the value of hours worked, at full rates, that the firm bills and collects.
What an Hourly Rate Has to Pay For
- The hour itself: the person’s salary cost for that hour.
- The hours they do not bill: leave, training, internal work, proposals.
- The cost of running the firm: benefits, rent, software, insurance, administration.
- A profit.
Rates set by looking only at what other firms charge can miss any of these. Rates set from your own costs cover them, and the market then shows how much room there is above them.
Step 1: Salary Cost per Hour
Salary cost per hour is each person’s annual salary divided by the hours they are paid for in a year. For example, an engineer earning $97,500 and paid for 1,950 hours costs $50 an hour in salary. For a rate by role, use the average for the role.
Use salary alone here, without benefits or payroll taxes. In this method those costs sit in overhead, and the overhead rate brings them back in step 2; adding them here as well would count them twice.
What Engineers Are Paid in Ontario
For a check on your own salary figures, Job Bank publishes wages by occupation from Statistics Canada’s Labour Force Survey.
| Civil engineers, 2023–2024 | Low | Median | High |
|---|---|---|---|
| Ontario | $30.50 an hour | $48.08 an hour | $72.12 an hour |
| Toronto region | $27.00 an hour | $51.28 an hour | $72.12 an hour |
Source: Job Bank, civil engineer (NOC 21300) wages in Ontario, updated 19 November 2025. At the Ontario median, an engineer paid for 1,950 hours earns about $93,800 a year (48.08 × 1,950). The figures are a reference for the market, not a rate: your own payroll is the number the sum needs.
Step 2: The Break-Even Multiplier
Work out your overhead rate: indirect costs divided by direct labour, the salary cost of project hours. Because non-billable salary time is counted in overhead, this rate already allows for the hours people do not bill. Add one, and you have the multiplier at which a billed hour covers its share of every cost.
For example, with an overhead rate of 150%, the break-even multiplier is 2.5. The $50 engineer has to bill at $125 just to cover costs.
Step 3: Add Profit
Choose the profit you want on each billed hour. For example, a 15% profit on the rate means the cost is 85% of it: $125 ÷ 0.85 ≈ $147. Rounded, a rate of about $150, which is a billing multiplier of 3.0 on salary.
| Example, round numbers | Sum |
|---|---|
| Salary cost per hour | $97,500 ÷ 1,950 = $50 |
| Break-even rate at a 150% overhead rate | $50 × 2.5 = $125 |
| Rate for a 15% profit | $125 ÷ 0.85 ≈ $147, rounded to $150 |
| Billing multiplier | $150 ÷ $50 = 3.0 |
Use your own salaries and your own overhead rate. A firm with a lower overhead rate can charge less for the same profit; one with a higher rate has to charge more, or bring its overhead down.
For example, the sum assumes every hour worked is billed and paid at the full rate. A firm that collects 90% of the value of its hours after write-offs needs $147 ÷ 0.90 ≈ $163 for the same profit. At 80% realization, a $150 rate brings in $120 an hour (150 × 0.80), below the $125 break-even. Use the realization your own invoices show, and divide by it.
Step 4: Check Against the Market
Compare the result with what your clients accept for each role. If your cost-based rate is well above the market, look first at the overhead rate, and within it at non-billable time. If it is well below, you may be leaving fees unclaimed. Either way, keep two figures apart. The break-even rate is the floor: below it, every hour billed and paid loses money, however busy the firm is. The target rate is where the firm earns the profit it planned. A rate between the two still covers costs, but earns less than planned.
Rates by Role
A small firm can bill by role or grade (principal, senior engineer, engineer, designer, technologist) rather than by named person. It is easier to explain, easier to keep current, and it lets the firm staff a project well without changing the fee.
| Example, round numbers | Average salary | Salary cost per hour | Rate at a 3.0 multiplier |
|---|---|---|---|
| Principal | $160,000 | $82.05 | $246 |
| Senior engineer | $120,000 | $61.54 | $185 |
| Engineer | $90,000 | $46.15 | $138 |
| Designer or technologist | $72,000 | $36.92 | $111 |
The example divides each salary by 1,950 paid hours and applies one multiplier to every role. One multiplier is simple and keeps the rates in proportion to pay. Some firms vary it, charging a higher multiplier for senior roles whose time is scarce and a lower one where the market is tight; if you do, check that the mix of hours on a typical project still clears the break-even multiplier.
Keep Rates Current
Review rates every year, when salaries change. Rates that stay flat while salaries rise lower the multiplier a little every year, and nobody decides it. On projects that run longer than a year, write the review into the proposal: the rates in it hold until a stated date, and later work is billed at the rates then current. Our article on the fee proposal covers where that line goes.
Where the Multiplier Really Ends Up
The billing multiplier is a plan. The net multiplier, worked out at year-end from real fees and direct labour, is what the firm achieved. If the net multiplier is well below the billing multiplier, the difference is in write-offs, over-budget fixed fees and discounts: in realization, not in the rate sheet. If the firm collects less than the full value of its hours year after year, allow for it in the rates, as step 3 shows, rather than hoping it improves.
Common Hourly Rate Mistakes
- Copying another firm’s rate sheet. Its overhead, salaries and profit are not yours.
- Adding benefits twice. Once in the salary cost and again through the overhead rate.
- Forgetting non-billable time. A rate built on 2,080 billable hours a year assumes nobody takes a holiday or writes a proposal.
- Leaving rates flat for years. The multiplier shrinks with every salary increase.
- Discounting the rate to win, then never restoring it. The discount becomes the rate for that client.
A Checklist for Setting Rates
- Take each role’s average salary, and divide by paid hours.
- Work out the overhead rate from last year’s accounts and timesheets.
- Multiply by one plus the overhead rate for the break-even rate.
- Divide by one minus the profit margin you want.
- Divide by the realization you expect, if some hours are usually written off.
- Round, and compare with what clients accept for each role.
- Write the rates, and the date they hold until, into every proposal.
- Compare the billing multiplier with the net multiplier at year-end.
- Review the rates when salaries change.
How We Approach This
A fee and margin review, project type by project type, is part of our growth work: fee levels, fixed fee or hourly, and where the firm undercharges, worked out from your own timesheets, fees and invoices.
Questions
How Do You Calculate an Engineering Hourly Rate?
Divide the salary by paid hours, multiply by one plus the overhead rate, and divide by one minus the profit margin you want. For example, $50 × 2.5 ÷ 0.85 is about $147, rounded to $150. If some hours are usually written off, divide by the share you expect to collect as well.
What Is a Typical Billing Multiplier for Engineers?
It depends on the firm’s overhead rate and profit target. In our example, a 150% overhead rate and a 15% profit give a multiplier of about 3.0 on salary.
What Do Civil Engineers Earn in Ontario?
Job Bank, using Statistics Canada’s Labour Force Survey for 2023–2024, puts the median at $48.08 an hour in Ontario and $51.28 in the Toronto region.
Should Rates Differ by Role?
Yes. Billing by role or grade, such as principal, senior engineer, engineer and technologist, is easier to explain and keep current than rates by named person.
How Often Should Hourly Rates Change?
Every year, when salaries change. Rates that stay flat while salaries rise lower the multiplier every year without anyone deciding it.
Sources
Updates
- : Rewritten at full length: benefits kept out of salary cost, Ontario wage figures from Job Bank, rates by role with a worked table, keeping rates current, common mistakes and a checklist.